SLM150 3D Printer

WIIBOOX®SLM150 METAL 3D PRINTER

High speed · High precision · High quality

Technical Principle

SLM printing uses selective laser melting technology which melts metal powders and solidifies layer by layer until a three-dimensional part is built. During the process, the ruler in the build chamber will pave one layer of the metal powder, a high powered laser selectively fuses the powder by tracing cross-section of the part on the surface of a powder bed and then a new coat of material is applied for the next layer. The whole process is in a high vacuum chamber or full of protective gas chamber to avoid the metal powder reacts with oxygen at high temperature.

Technological Superiority

Wiiboox is using a high energy and fine spot laser, The equipment can complete complex parts in a very short period time while using conventional methods that will take several weeks or even months to complete in comparison. Parts not only have precise dimension, high tensile and high density, but also excellent in mechanical properties. Mainly used for rapid production of high-precision, high quality metal parts.

Multiple Printing Materials

Wiiboox SLM150 Metal 3D Printer supported printing materials: Stainless steel (316L), Aluminium alloy (AlSi10Mg), Titanium alloy (TC4), Cobalt chromium alloy (MP1), Die steel (MS1), Superalloy (IN718), High conductivity copper (QCr1) etc.

Customer Cases

Wiiboox SLM150 Metal 3D Printer can print metal parts with complex structure to help shorten product development cycle and reduce R & D cost.

Printing Material: Die steel H13

Printing Size: 210X140X160mm

Printing Technology: SLM

Problems to be Solved: solving the problem of thermal stress concentration of injection parts to improve the precision, so as to further improve the life of the mold.

Printing Material: Stainless steel 316L

Printing Size: 180X130X180mm

Printing Technology: SLM

Problems to be Solved: shortening the R & D cycle and acquiring more accurate test result.

Printing Material: Copper alloy

Printing Size: 220X220X100mm

Printing Technology: SLM

Problems to be Solved: good density and good mechanical properties, no need of post-treatment process.

Printing Material: Cobalt chromium alloy

Printing Size: 300X300X80mm

Printing Technology: SLM

Problems to be Solved: suitable for customization of single piece or small batch of functional parts.

Specifications

Technical Parameters

Laser System

Type:Fiber laser
Wavelength:1064nm
Power:200W / 500W

Recoating System

Process:scraper paving
Normal Build:0.05mm
Quick Build:0.05~0.10mm
Precision Build:0.02~0.05mm

Optical & Scanning

Beam (diameter@1/e2):0.04~0.15mm
Scanning Galvanometer:High Speed Scanning Galvanometer
Parts Scanning Speed:1.0~2.0m/s (recommended)
Blank Jumping Speed:10.0m/s (recommended)
Reference Building Speed:2~15cm³/h

Shield System

Protective gas:N2 / Ar
Flow Control:0~3L /min intellient adjustment
Dust extraction control:High efficiency Protection recycling system

Build Vat

VolumeApprox: 4.5L
Size:150mm(X) × 150mm(Y) × 200mm(Z)
Max Weight:20kg
Type:Precision resistor heater
Materials:Stainless Steel / Die Steel / Titanium Alloy / Aluminium Alloy / Co-Cr Alloy / Nickel Alloy / Cuprum etc.

Software

Network:Ethernet, TCP/IP, IEEE802.3
Control Software:iSLM(Presto SLM)
Date Preparation Software:3dMagic
Data Interface:CLI file, SLC file, STL file

Installation Condttion

Power:200~240VAC 50/60Hz, single phase, 15Amps
Ambient Temperature:20-26ºC
Relative Humidity:Less than 40%, non-condesing
Size:1.55m(W)×1.10m(D)×1.90m(H)(Operating computer is not included) Weight:Approx. 1000kg

Warranty

Laser:5000 hours or 12 months (whichever comes first)
Main Machine:12 months from installation date

Contact Us

Ludrick Barnard
+27(0)82 780 7305
info@wiiboox-sa.co.za
Physical Addresses
The Imperative Centre,
1st Floor, Kara Place, Block F,
Olive Grove Industrial Estate, Old Paardevlei Road,
Somerset West
Unit D4,
The Studio Office Park
Ateljee Street
Randparkridge

Open chat